SS Series

Clear
$

General

SS Series:

The Stelron SS series unit consists of a single hardened slide bar having a flat surface ground over its full slide length, two in line re-circulating linear ball bearings, and an eccentric adjustable roller, all assembled into a compact housing. The slide bar ends may be obtained either with plain ends or with flat square surfaces to facilitate mounting of tools and actuating links.

These units combine the compactness of a single slide bar with a feature for eliminating any play or shake between the rolling elements. This is done by means of an eccentric pin and roller contacting the flat surface of the slide bar thus preventing any rotation or play.

The housing incorporates felt wipers and mounting holes.

Anti-Friction Slide Introduction:

The Stelron anti-friction slide units incorporate tried and proven linear ball bearings into compact assemblies combining rolling elements for low friction, hardened contact surfaces for long life and minimum wear, with negligible or zero backlash. Long, unrestricted stroked are not a limitation due to the use of re-circulating ball races in the bearing.

Application:

Machine parts or tools which require “in-line” motion can be readily mounted to the Stelron Anti-Friction Slide units either on the surfaces provided at the slide bar end plates, or on the housing when the slide bar ends are fixed, thus permitting the housing to move.

Where translational or incremental movement in a plane with the sensitivity and accuracy of a ball bearing is required, the Stelron X-Y Anti-Friction Slides fulfill a wide range of applications.

Materials:

Shafts are hardened and ground steel. End plates and housings are generally steel except in larger sizes where aluminum is used to reduce weight. With few exceptions, all external surfaces are ground. Housings and end plates have black oxide or anodized surface treatment.

Lubrication & Friction:

Integral oil cups are usually provided for application of light grade oil. The standard use of felt wipers absorbs and distributes the lubricant, excludes most foreign matter and offers less resistance then Neoprene type seals.

The co-efficient of friction for the bearings without wipers is approximately .003.

Clearance:

All standard units have approximately .001 mean clearance between the shaft and bearing bores. Shafts providing a line to line fit can be supplied when specifically requested.

Capacity Ratings:

All standard units have approximately .001 mean clearance between the shaft and bearing bores. Shafts providing a line to line fit can be supplied when specifically requested.

Stroke Lengths:

Due to a large variation in desired stroke requirements, our facilities enable us to provide ANY length BELOW that tabulated for various units — longer lengths incur the additional cost of shaft over and above those tabulated.

Technical

DIMENSIONS:
Model No. SS1 SS2 SS3 SS4 SS5 SS6 SS7 SS8
A To 6″ To 7″ To 8″ To 10″ To 12″ To 14″ To 16″ To 20″
B 38 38 7⁄16 ½ ½ 3⁄4 1 1
C 1 ½ 1 78 2 ½ 3 ¼ 4 3⁄4 5 ½ 6 8
D 2 ¼ 2 5⁄8 3 3⁄8 4 ¼ 5 3⁄4 7 8 10
E 5⁄32 3⁄16 3⁄16 7⁄32 9⁄32 38 38 7⁄16
F 11⁄16 7⁄8 1 1⁄8 1 9⁄16 1 15⁄16 2 3⁄4 3 3 5⁄8
G ¼ 3⁄8 ½ 3⁄4 1 1 ¼ 1 ½ 2
H 5⁄8 3⁄4 7⁄8 1 1 1⁄8 1 ¼ 1 ½ 2
J 3⁄4 7⁄8 1 ¼ 1 ½ 2 2 ½ 3 4 ½
K 1 1 1⁄4 1 ½ 2 2 ½ 3 ½ 3 3⁄4 7
L .312 .375 .625 .687 .938 1.250 1.500 1.750
M .187 .250 .375 .500 .750 .875 1.125 1.500
N 5⁄32 .201 .201 17⁄64 21⁄64 25⁄64 17⁄32 17⁄32
P *10-32 ¼-20 ¼-20 5⁄16-18 3⁄8-16 7⁄16-14 5⁄8-11 5⁄8-11
R 5⁄32 5⁄32 3⁄16 3⁄16 ¼ 5⁄16 38 ½
S 5⁄16 38 ½ ½ 58 58 3⁄4 1
T 4-40 6-32 8-32 10-32  ¼-20 5⁄16-18 3⁄8-16 ½-13

 

Catalog/Service Manual

Contact Us

Feel free to contact us about this product!